This quick start guide provides an end-to-end setup process for installing and running Cumulus RMP, as well as a collection of example commands for getting started after installation is complete.

Prerequisites

Intermediate Linux knowledge is assumed for this guide. You should be familiar with basic text editing, Unix file permissions, and process monitoring. A variety of text editors are pre-installed, including vi and nano.

You must have access to a Linux or UNIX shell. If you are running Windows, use a Linux environment like Cygwin as your command line tool to interact with Cumulus RMP.

If you are a networking engineer but are unfamiliar with Linux concepts, refer to this reference guide for examples of the Cumulus Linux CLI and configuration options, and their equivalent Cisco Nexus 3000 NX-OS commands and settings. You can also watch a series of short videos introducing you to Linux and Cumulus Linux-specific concepts.

Contents

 This chapter covers ...

Setting Up a Cumulus RMP Switch

To set up a Cumulus RMP switch: 

  1. Rack the switch and connect it to power.
  2. Cable all the ports.
  3. Log in and change the default password.
  4. Configure switch ports and a loopback interface, if needed.

This quick start guide walks you through the steps necessary to get your Cumulus RMP switch up and running after you remove it from the box. 

Upgrading Cumulus RMP

If you are running a Cumulus RMP version earlier than 3.0.0, you must perform a complete install. If you already have Cumulus Linux 3.0.0 or later installed on your switch, read Upgrading Cumulus Linux for considerations before you start the process.

Getting Started

When bringing up Cumulus RMP for the first time, the management port makes a DHCPv4 request. To determine the IP address of the switch, you can cross reference the MAC address of the switch with your DHCP server. The MAC address is typically located on the side of the switch or on the box in which the unit is shipped.

Login Credentials

The default installation includes one system account, root, with full system privileges, and one user account, cumulus, with sudo privileges. The root account password is set to null by default (which prohibits login), while the cumulus account is configured with this default password:

CumulusLinux!

In this quick start guide, you use the cumulus account to configure Cumulus RMP.

For best security, change the default password (using the passwd command) before you configure Cumulus RMP on the switch.

All accounts except root are permitted remote SSH login; you can use sudo to grant root-level access to a non-root account. Commands that change system configuration require this elevated level of access.

For more information about sudo, read Using sudo to Delegate Privileges.

Serial Console Management

Cumulus Networks encourages you to perform management and configuration over the network, either in band or out of band. Use of the serial console is fully supported; however, many customers prefer the convenience of network-based management.

Typically, switches ship from the manufacturer with a mating DB9 serial cable. Switches with ONIE are always set to a 115200 baud rate.

Wired Ethernet Management

Switches supported in Cumulus RMP contain a number of dedicated Ethernet management ports, the first of which is named eth0. These interfaces are geared specifically for out-of-band management use. The management interface uses DHCPv4 for addressing by default. While it is generally recommended to not assign an address to eth0, you can set a static IP address with the Network Command Line Utility (NCLU).

Example IP Configuration

Set the static IP address with the interface address and interface gateway NCLU commands:

cumulus@switch:~$ net add interface eth0 ip address 192.0.2.42/24
cumulus@switch:~$ net add interface eth0 ip gateway 192.0.2.1
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

These commands produce the following snippet in the /etc/network/interfaces file:

auto eth0
iface eth0
    address 192.0.2.42/24
    gateway 192.0.2.1

In-Band Ethernet Management

All traffic that goes to the RMP switch through an interface called vlan.1 is marked for in-band management. DHCP is enabled on this interface by default and you can confirm the IP address at the command line. However, if you want to set a static IP address, change the configuration for vlan.1 in the /etc/network/interfaces file.

auto vlan.1
iface vlan.1
    address 10.0.1.1/24
    gateway 10.0.2.1

Configuring the Hostname and Time Zone

To change the hostname, run net add hostname, which modifies both the /etc/hostname and /etc/hosts files with the desired hostname.

cumulus@switch:~$ net add hostname <hostname>
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

The command prompt in the terminal does not reflect the new hostname until you either log out of the switch or start a new shell.


To update the time zone, update the /etc/timezone file with the correct timezone, run dpkg-reconfigure --frontend noninteractive tzdata, then reboot the switch:

cumulus@switch:~$ sudo nano /etc/timezone
cumulus@switch:~$ sudo dpkg-reconfigure --frontend noninteractive tzdata
cumulus@switch:~$ sudo reboot

Testing Cable Connectivity

By default, all data plane ports and the management interface are enabled.

cumulus@switch:~$ net add interface swp1
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

To administratively enable all physical ports, run the following command, where swp1-52 represents a switch with switch ports numbered from swp1 to swp52:

cumulus@switch:~$ net add interface swp1-52
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

To view link status, use the net show interface all command. The following examples show the output of ports in admin down, down, and up modes:

cumulus@switch:~$ net show interface all
       Name                      Speed    MTU    Mode           Summary
-----  ------------------------  -------  -----  -------------  --------------------------------------
UP     lo                        N/A      65536  Loopback       IP: 10.0.0.11/32, 127.0.0.1/8, ::1/128
UP     eth0                      1G       1500   Mgmt           IP: 192.168.0.11/24(DHCP)
UP     swp1 (hypervisor_port_1)  1G       1500   Access/L2      Untagged: br0
UP     swp2                      1G       1500   NotConfigured
ADMDN  swp45                     0M       1500   NotConfigured
ADMDN  swp46                     0M       1500   NotConfigured
ADMDN  swp47                     0M       1500   NotConfigured
ADMDN  swp48                     0M       1500   NotConfigured
ADMDN  swp49                     0M       1500   NotConfigured
ADMDN  swp50                     0M       1500   NotConfigured
UP     swp51                     1G       1500   BondMember     Master: bond0(DN)
UP     blue                      N/A      65536  NotConfigured
DN     bond0                     N/A      1500   Bond           Bond Members: swp51(UN)
UP     br0                       N/A      1500   Bridge/L3      IP: 172.16.1.1/24
                                                                Untagged Members: swp1
                                                                802.1q Tag: Untagged
                                                                STP: RootSwitch(32768)
UP     red                       N/A      65536  NotConfigured
ADMDN  rename13                  0M       1500   NotConfigured
ADMDN  vagrant                   0M       1500   NotConfigured

Configuring Switch Ports

Layer 2 Port Configuration

Cumulus RMP does not put all ports into a bridge by default. To configure a front panel port or create a bridge, edit the /etc/network/interfaces file. After saving the file, use the ifup command to activate the change.

Examples

Example One

In the following configuration example, the front panel port swp1 is placed into a bridge called bridge. The NCLU commands are:

cumulus@switch:~$ net add bridge bridge ports swp1
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

The commands above produce the following /etc/network/interfaces snippet:

auto bridge
iface bridge
	bridge-ports swp1
	bridge-vlan-aware yes

Example Two

You can add a range of ports in one command. For example, add swp1 through swp10, swp12, and swp14 through swp20 to bridge:

cumulus@switch:~$ net add bridge bridge ports swp1-10,12,14-20
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

This creates the following /etc/network/interfaces snippet:

auto bridge
iface bridge
  	bridge-ports swp1 swp2 swp3 swp4 swp5 swp6 swp7 swp8 swp9 swp10 swp12 swp14 swp15 swp16 swp17 swp18 swp19 swp20
	bridge-vlan-aware yes

To view the changes in the kernel, use the  brctl command:

cumulus@switch:~$ brctl show
bridge name     bridge id              STP enabled     interfaces
br0             8000.089e01cedcc2       yes              swp1
A script is available to generate a configuration that places all physical ports in a single bridge.

Layer 3 Port Configuration

To configure a front panel port or bridge interface as a layer 3 port, use NCLU.

In the following configuration example, the front panel port swp1 is configured as a layer 3 access port:

cumulus@switch:~$ net add interface swp1 ip address 10.1.1.1/30
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

This creates the following /etc/network/interfaces snippet:

auto swp1
iface swp1
  address 10.1.1.1/30

To add an IP address to a bridge interface, you must put it into a VLAN interface:

cumulus@switch:~$ net add vlan ip address 10.2.2.1/24
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

This creates the following /etc/network/interfaces snippet:

auto bridge
iface bridge
    bridge-vids 100
    bridge-vlan-aware yes

auto vlan100
iface vlan100
    address 192.168.10.1/24
    vlan-id 100
    vlan-raw-device bridge

To view the changes in the kernel, use the ip addr show command:

cumulus@switch:~$ ip addr show
...
 
4. swp1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bridge state UP group default qlen 1000
    link/ether 44:38:39:00:6e:fe brd ff:ff:ff:ff:ff:ff
...
  
14: bridge: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
    link/ether 44:38:39:00:00:04 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::4638:39ff:fe00:4/64 scope link
       valid_lft forever preferred_lft forever
...

Configuring a Loopback Interface

Cumulus RMP has a loopback preconfigured in the /etc/network/interfaces file. When the switch boots up, it has a loopback interface, called lo, which is up and assigned an IP address of 127.0.0.1.

The loopback interface lo must always be specified in /etc/network/interfaces and must always be up.

To see the status of the loopback interface (lo), use the net show interface lo command:

cumulus@switch:~$ net show interface lo

    Name    MAC                Speed      MTU  Mode
--  ------  -----------------  -------  -----  --------
UP  lo      00:00:00:00:00:00  N/A      65536  Loopback

IP Details
-------------------------  --------------------
IP:                        127.0.0.1/8, ::1/128
IP Neighbor(ARP) Entries:  0

Note that the loopback is up and is assigned an IP address of 127.0.0.1.

To add an IP address to a loopback interface, configure the lo interface with NCLU:

cumulus@switch:~$ net add loopback lo ip address 10.1.1.1/32
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

You can configure multiple loopback addresses by adding additional address lines:

cumulus@switch:~$ net add loopback lo ip address 172.16.2.1/24
cumulus@switch:~$ net pending
cumulus@switch:~$ net commit

This creates the following snippet in the  /etc/network/interfaces file:

auto lo
iface lo inet loopback
    address 10.1.1.1/32
    address 172.16.2.1/24

Assigning Port-Based IP Addresses

You can assign an IP address and other DHCP options based on physical location or port regardless of MAC address to clients that are attached directly to the Cumulus Linux switch through a switch port. This is helpful when swapping out switches and servers; you can avoid the inconvenience of collecting the MAC address and sending it to the network administrator to modify the DHCP server configuration.

Edit the /etc/dhcp/dhcpd.conf file and add the interface name ifname to assign an IP address through DHCP. The following provides an example:

host myhost {
     ifname = "swp1" ;
     fixed_address = 10.10.10.10 ;
}
Write a comment…