Cumulus NetQ 3.0 Release Notes

Download 3.0 Release Notes xls    Download all 3.0 release notes as .xls

3.0.0 Release Notes

Open issues in 3.0.0

Issue IDDescriptionAffectsFixed
NETQ-6673 Infra: NetQ VM installation fails if the designated disk size is greater than 2TB. To work around this issue, specify the disk for cloud deployments to be between 256GB and 2TB SSD, and for on-premises deployments to be between 32 GB and 2TB.2.4.0-
NETQ-5833 Switch upgrade of Cumulus Linux in the lifecycle management feature fails when attempted by a user with a standard or sudo user role and custom password credentials. To work around this issue, upgrades should be performed by users with root or sudo user role and an SSH key. Optionally, upgrade using a root user role with custom password.
NETQ-5808 When upgrading to NetQ 3.0.0, if you are using NetQ Agent 2.3.1 or earlier and have MLAG configured, the MLAG service becomes unresponsive. To resolve this issue, upgrade your NetQ Agents to version
NETQ-5774 When installing NetQ on switches running in Cumulus Linux 3.7.x with management VRF configured, the CLI and Agent server are configured as follows:
netq config add cli server <ipaddr> vrf mgmt
netq config restart cli

netq config add agent server <ipaddr> vrf mgmt
netq config restart agent

This results in netqd running in both default and management VRF and the NetQ Agent running in default VRF. In this scenario, the NetQ Agent status is not reported correctly to the management VRF. To workaround this issue: If you have management VRF configured, run the following commands:
systemctl stop netqd.service
systemctl disable netqd.service
systemctl enable netqd@mgmt.service
systemctl restart netqd@mgmt.service

If you have default VRF configured, run the following commands:
systemctl stop netqd@mgmt.service
systemctl disable netqd@mgmt.service
systemctl enable netqd.service
systemctl restart netqd.service
NETQ-5768 When multiple premises are deployed and Cumulus Linux upgrades have been performed on switches using the lifecycle management feature, the Upgrade History card displays history for all premises rather than only those for the selected premises.
NETQ-5752 Performing an upgrade using the lifecycle management feature fails intermittently when SSH key switch access authorization is used. To work around this issue, use basic authentication or retry an upgrade job that uses SSH key authorization.
NETQ-5737 UI: Warnings might appear during the post-upgrade phase for a Cumulus Linux switch upgrade job. They are caused by services that have not yet been restored by the time the job is complete. Cumulus Networks recommend waiting five minutes, creating a network snapshot, then comparing that to the pre-upgrade snapshot. If the comparison shows no differences for the services, the warnings can be ignored. If there are differences, then troubleshooting the relevant service(s) is recommended.3.0.0-3.2.0
NETQ-5591 UI: The lifecycle management feature does not present general alarm or info events; however, errors related to the upgrade process are reported within the NetQ UI.3.0.0-
NETQ-5571 UI: The legend and segment colors on Switches and Upgrade History card graphs sometimes do not match. These cards appear on the lifecycle management dashboard (Manage Switch Assets view). Hover over graph to view the correct values.3.0.0-3.2.0
NETQ-5529 UI: Snapshot comparison cards may not render correctly after navigating away from a workbench and then returning to it. If you are viewing the Snapshot comparison card(s) on a custom workbench, refresh the page to reload the data. If you are viewing it on the Cumulus Default workbench, after refreshing the page you must recreate the comparison(s).2.4.0-2.4.1, 3.0.0-3.2.0
NETQ-4927 Admin UI: If the Master Installation phase fails during NetQ installation, refreshing the page causes the error log to be lost. On failure, download the error log, then run netq bootstrap reset followed by netq bootstrap master interface on the node before restarting the installation process.2.4.1-
NETQ-3451 UI: If either the peer_hostname or the peer_asn is invalid, the full screen BGP Service card does not provide the ability to open cards for a selected BGP session.2.3.0-2.4.1, 3.0.0-3.2.0

Fixed issues in 3.0.0

Issue IDDescriptionAffects
NETQ-5182When a switch or host reports its memory size in GB rather than MB, the NetQ Agent cannot parse the information and thus fails to register with the NetQ server. Contact customer support if you run into this issue.2.4.0-2.4.1